Every partition matters. Start with the right gasket drawing. sales@ferrobend.com +91-8369719424

Equipment / Heat Exchanger

Heat Exchanger Gaskets

Sealing for shell-and-tube exchanger joints. Match the perimeter, partition layout and gasket construction to the equipment drawing and service conditions.

Heat Exchanger GasketsIllustrative heat exchanger gasket with a metal-faced perimeter, twelve bolt holes and internal pass partition bars.

THE CONSTRUCTION

Seal the perimeter.
Define the partitions.

Shell-and-tube exchanger gaskets seal removable channel, cover, tubesheet and shell joints as required by the equipment design. The perimeter controls external leakage, while partition-bar seals separate adjacent chambers at the relevant joint.

Match the gasket to the seating faces, grooves and partition lands. Review shell-side and tube-side fluids, differential pressure and thermal cycling together with the available bolt load.

For plate-pack sealing, see Plate Heat Exchanger Gaskets ↗

Equipment scopeShell-and-tube joints
Drawing detailsPerimeter + partitions
SelectionConstruction + materials

TECHNICAL REFERENCE

Standards & material specifications

Read equipment requirements, gasket construction and drawing details together.

Equipment & gasket references

Heat exchanger design and gasket specification references
TEMA StandardsShell-and-tube exchanger requirements. Use the project-specified edition, exchanger class and approved equipment drawing for gasket selection.
ASME BPVC VIII-1Pressure-vessel design and construction requirements where Division 1 governs the equipment. Confirm the project code and joint design.
ASME B16.20Applies to covered metallic gasket constructions for matching standard flanges. Equipment-specific channel and tubesheet dimensions follow the approved drawing.

Partition layouts, gasket seating load and assembly requirements need joint-specific verification. Standard flange dimensions apply where the actual connection matches their scope.

Construction & material selection

Heat exchanger gasket construction and material selection
Metal jacketedSpecify jacket alloy, filler and finished thickness independently. Define partition-bar junctions and enclosure details on the drawing.
KammprofileSpecify core alloy, serrations and facing grade/thickness. Pass-bar construction and locating details require an agreed design.
Spiral woundSpecify winding, filler and locating arrangement. Partitioned designs require a defined construction compatible with the equipment joint.

Specify raw-stock requirements separately, such as ASTM A240/A240M for suitable stainless sheet or plate. Soft-sheet alternatives require approval for the exchanger class and service.

EXPLORE THE PARTITION LAYOUTS

Four layouts. Defined by the equipment.

Illustrative gasket geometries within this equipment application. Flow-pass arrangements depend on the complete exchanger design. Confirm dimensions, bar junctions and construction against the drawing.

Perimeter Ring gasket layoutIllustrative oblique ring gasket layout with no partition bars. Final dimensions and construction follow the equipment drawing.Continuous perimeter
01 / Without partition bars

Perimeter Ring

A continuous perimeter seal for a joint without a partition-bar requirement. Match the seating width, groove geometry and finished section to the equipment drawing.

Single Partition Bar gasket layoutIllustrative oblique ring gasket layout with one diametric partition bar. Final dimensions and construction follow the equipment drawing.Diametric partition
02 / One divider

Single Partition Bar

A diametric bar follows the channel partition at the gasketed face. Specify bar width, position and the junctions where it meets the perimeter seal.

Parallel Partition Bars gasket layoutIllustrative oblique ring gasket layout with two parallel partition bars. Final dimensions and construction follow the equipment drawing.Parallel partitions
03 / Parallel dividers

Parallel Partition Bars

Two parallel bars follow the corresponding partition lands. Their spacing, length and seating height must match the mating equipment faces.

Cross Partition Bars gasket layoutIllustrative oblique ring gasket layout with intersecting partition bars. Final dimensions and construction follow the equipment drawing.Cross partition layout
04 / Intersecting dividers

Cross Partition Bars

Intersecting bars follow a cross-shaped partition layout. Define the central junction and perimeter connections, including the required sealing continuity.

Need a Heat Exchanger Gasket for Your Equipment?

Share the equipment drawing, gasket location, partition details, materials, service conditions and quantity.

Request a Quote